Here’s little tutorial on BMW E-series coding programs installation.
- From Automotive Wiki from mr-fix. Jump to: navigation, search. V49 (December 2012) v52 (March 2014) v53.3 (August 2014) - Download.
- Sp Daten V49. 49.4 + SP daten 2.49.4 torrent. My car is a 2009 E90, and will need the E89 files if I'm not mistaken Thanks again, Mike PM sent.
- Aug 20, 2010 Windows 98 was never tested or designed for more than 512mb of ram. There are patches and 'workarounds' for this, but youd be better of.
Disclaimer: The document was translated from Korean. You are at your risk.
Ediabas Inpa / BMW Standard Tools 2.12 +SP-Daten V49.0 Installation Deutsch / German Win 7 & 8.
Part I. Required files
1. INPA
2. BMW Coding Pack
3. BMW Coding Tool
→ Download E_coding.zip
Unpack and use
4. SP-DATEN
→ Download and use the data file for BASE and car https://mega.nz/#F!ukQzzBwb!bH9cRXpvW4xiTLr-N10CjQ
! iAJg_VqYENXBCaGLS-AvFvhPSNEae2mp-aWtuYOHGv8 (E_coding.zip decryption key)
Part II. Install the INPA program
1. Materials
(1) Coding required cable: BMW INPA K+DCAN cable
(2) Programs required for coding: INPA / NCS Expert
(3) Own vehicle information file (SP-Daten, SP-Daten capacity of 30 ~ 40GB per vehicle)
2. INPA program installation
(1) INPA / K + D CAN drive installation
If you unzip it, there are three folders in Step 1, 2, 3, and there are installation instructions, a description PDF document,
1) Copying the entire EC-Apps under the 01_Step1 directory to C: /
2) Run NFS / Entpackt / disk1 / SETUP.exe under the directory 01_Step1
Install
If not, copy all of these NFS directories to C: / and install them)
Note 1. In Windows 8.1 32bit, copy the file under disk1 to C; /
NTVDM automatically download and run)
Note 2. If the program fails to install again after the installation fails, copy the previously copied C: / EC-Apps
Clear all and copy again
Select Window XP on the screen
The remaining selection values
User mode / Parametrienen einer neuen Configuration ohen Dafer / OBD / KeinApi-Trace / Kein IFH-TRACE / Komfor (.IPO) selection
The first time you install regsvr32, the two * .ocx files will fail to register, but if you uninstall and reinstall the program you just installed from the control panel, the ocx file will be registered normally.
In particular, the message “The program is not installed properly” appears on Windows 7/8. Select the program installed correctly ”
3) Run INSTALL / Instprog.exe under the directory 02_Step2
(Copy and run under C: temp, but not on other drives)
Select “ENGLISH” on the screen, press Continue / Continue and never change the folder or drive to install.
In the Configuration window
Select “Bmw Group Rectification programs UK” → Continue
EDIABAS 6.4.3 → Update
INPA 5.0.1 → Update
NCS Expert 3.0.8 → Check Complete → Continue
4) INSTALL / Instprog.exe under the 03_Step3 directory
(Copy and run under C: temp, but not on other drives)
3) in the same way
Old verstion delete → Yes
5) Overwrite inpa.ini under c: / EC-APPS / INPA / CFGDAT with inpa.ini in the INPA folder.
3. Cable connections and port settings
(1) Plug OBD cable into USB port and select manual drive installation
1) Install it as a drive under the drive under the INPA folder, and when installed, recognize USB Serial Port
2) In the USB Serial Port property, set Port Setting / Advanced / Com Port No. 1, Response Time 1
Sp Daten V49 1
(2) Run Drive_D_CAN_USB / OBDSetup.exe under INPA directory and reboot
INPA installation complete
(3) Confirmation of installation: Execute c: /EC_Apps/INPA/BIN/inpaload.exe and Battery / Ignition
If you see two black dots on the installation succeeded
Part III. Installing BMW Standard Tool from BMW Coding Pack
1. When unzipping, four folders with numbers 1 ~ 4 are created, and BMW Standard Tool 2.12 installation
(Be sure to run the program under BMW Coding Pack folder)
(1) Before running the program, open the Compatibility tab in the properties of the installation file
→ Change Compatibility by selecting Windows XP Service Pack 3
(2) Installation file Click “English” in English / German selection window.
(All installation programs will be deleted when English is selected)
(3) Select German / Weiter (Next) “Ich akzeptieredie Vereinbarung”
→ Press “Weiter” 3 times to set the directory (set to 4 folders default) and add 1 folder
Microsoft dynamics rms keygen crack. (4) Zus? Zliche Aufgaben ausw? Len
→ Check out two of the above four check boxes: “Datensicherung” (data backup)
(Leave the other two checked and press the next one to pop up a popup window)
(5) Leave the STD: OBD default value on the next Hardware Interface screen
(6) COM port number checked in Device Manager 1 Select “COM1” and then USB auf Serial
Adapter Check
(7) Click Next and then click Installer to start the installation
Select “Ignore” if error screen appears and select “Ignore” if error screen appears (error 2)
2. When the installation is complete, go to the 3-UPDATE folder and add three folders (EC-APPS, EDIABAS, Gislook gismeta for mac.
NCSEXPER) whole
Copy to C: → Overwrite existing file with latest English version)
3. After copying the update file, copy the “BMW Coding Shorcuts” folder 4 to the desktop
Part IV. Installing BMW Coding Tools and SP_DATEN
1. Unzip the file into C: / windows / system, C: / windows / system32, C: / windows / Syswow64
Copy comdlg32.ocx, mscomctl.ocx under BMW Coding Tool folder
2. Open a command window in administrator mode and type
(Enter the Windows program app and right-click command to run as administrator)
“Regsvr32 comdlg32.ocx”, “regsvr32 mscomctl.ocx” → After registry registration succeeded
Close the command window and run BMW Coding Tools
3. Press the “Select SP-source” button on the right “SP daten” to find your vehicle information daten file
Select ah Select
Sp-daten-e89_v49
4. Click the “UPdate SP-source” button on the right “SP daten” to link and copy the daten file
![V49 V49](https://1.bp.blogspot.com/-EXwFfLRI5BQ/XUzC2837mtI/AAAAAAAADQU/2Lo41nA-77ADeQmg4yk5ocnSITC-mvGLACLcBGAs/s640/cgdi-bmw-cas3-downgrade-2.jpg)
5. Down the received dummy profile (NCExpert Profile / NCSDUMMY4.PFL) to c: / NCSEXOER / PFL
![Sp daten v55 download Sp daten v55 download](https://lh6.googleusercontent.com/-3TLcGKW07c8/TxEfnZijDHI/AAAAAAAAAvk/etQ9PQ7n_aY/s1600/GS6-53BZ.jpg)
copy
All programs for E series coding installation is complete.
It is not easy. You must follow each one step by step. Keep the order …
Who Viewed This Article Also Views:
Free Download BMW Standard Tools 2.12 coding software
BMW Standard Tools is the software suite distributed by BMW Group that contains several interoperating applications and drivers, including NCS Expert, WinKFP, NFS, INPA, Tool32, and others. Here is the free download link for V2.12.
Hardware:
A PC (Operating system: Win XP 32 bit /VMware Win 7 32 or 64 bit) An INPA/EDIABAS K+DCAN USB Diagnostic cable (cheap €19 in eobd2.fr)
How to setup BMW Standard Tools 2.12?
Step 1: Download BMW Standard Tools 2.12
Download here and install follow system prompts:
http://www.mediafire.com/download/qldyddn48ffzrwn/BMW+Standard+Tools+2.12.rar
Step 2: Download and install INPA
http://www.maxdown.org/download.php?file=BMW%20Inpa/Ediabas%20v5.06&host=b
Step 3: Download and install NCS Expert ENG
Download NCS-Expert software here and install
http://www.mediafire.com/download/en2xcszq46vaipm/NCSEXPER32_ENG.zip
Step 4: Download and configure INPA K+DCAN cable
Make sure your EDIABAS should already be configured to STD:OBD for use with INPA cable.
Download EDIABAS configurator here:
http://www.mediafire.com/download/x1r66eesv14lx88/ediabas+konfigurator2.0.0.exe
This tool (in C:EDIABASEdiabas-Konfigurator folder) allows you to easily change the ediabas.ini to your desired interface. So if you are switching from INPA to E-Sys you could use this to switch from STD:OBD to ENET. Set COM port for INPA cable Connect the INPA DCAN cable with PC
Install device deriver Come to My Computer>>Device Manager>>Ports (COM&LPT) In this case it's COM5. We need to change this in the obd.ini file located in the c:ediabasbin folder. Right click on your INPA cable driver for example mine is labeled 'USB Serial Port' and click on properties. Now in the property window click on the advanced tab.
Now every driver is different but the important part is the settings such as latency timer and received and transmit bytes. See pic bellow for the ideal settings. You may also change the COM port number here as well for tutorial I left it at 5. Once your changes are done we can proceed by clicking OK to accept the changes. No close all windows to return to the desktop.
Step 5: Change the OBD Browse to C:EDIABASBIN and find file obd.ini and open it with an editor (e.g Notepad) First 3 lines will look like this.. [OBD] Port=Com1 Hardware=USB Need to change the Port to reflect our INPA cable which in our case is COM port 5. So change it to look like this.. [OBD] Port=Com5 Hardware=USB When done click File -> Save and exit
NOTE: Remember which USB port you connected your cable to as plugging it into a different USB port will allocate the INPA cable to a different COM port and neither tool will see the cable until the original USB port is used again or changed in device manager and obd.ini as mentioned above.Now to test if your cable installed correctly. Plug it into the vehicle's OBD port and open INPA.
Step 6: SPDATEN Files Download and install SPDaten files (always recommend the latest)
in this case it is 50.2 until I finish zipping and upload SPDatens 51.0 and upload it to share. (Follow the instructions provided at the end of the blog labeled 'How to start WinKFP' which will explain how to import the SPDaten files to WinKFP)
Once downloaded you can now
**EDITED 10-12-2013**
For NCSExpert to install or update the daten files, copy the files from SP-daten-E##daten to the C:NCSEXPERDATENE## (where E## is whatever chassis you're updating). You will also want to copy the files from SP-daten-E##SGDAT to C:NCSEXPERSGDAT (they're not separated into different chassis in NCS Expert, so you just want to copy and paste everything to that directory. Overwrite everything it asks about). Then copy the files from SP-daten-E##ECU to C:EDIABASECU
After copying the daten files to c:NCSEXPERDATENE## copy the following files to the following locations:
copy C:NCSEXPERDATENE##*.000 C:NCSEXPERDATEN copy C:NCSEXPERDATENE##*.DAT C:NCSEXPERDATEN copy C:NCSEXPERDATENE##*.ASC C:NCSEXPERDATEN
PS: How to start WinKFP?
1. Install WinKFP and come to direction
2. After installation the directory (Drive letter):EC-APPSNFSSGDAT contains file CABI.h only, and doesn’t contains files, required for working.
3. Mount the Progman disk in virtual drive (or insert in usual DVD-drive), extract all files SP-daten-Exx.rar from directory (Drive letter):CIP-Installerbin, each one in its own directory. (You must get directories like SP-daten-Exx)
4. Now copy all *.IPO files from every directory (Drive letter):SP-daten-Exxsgdat to directory (Drive letter):EC-APPSNFSSGDAT. For this purpose better use Total Commander, it allows to overwrite elder files with newest. This directory now looks like this:
5. In the same way refresh directory (Drive letter):EDIABASEcu with files taken from (Drive letter):SP-daten-Exxecu 6. Run WinKFP
6. Run WinKFP software
7. Choose “Import/Export – Import – Assemly line data” and import all data needed from directories (Drive letter):SD-daten-ExxDATA Details how to import assembly line data are given in official manual for WinKFP
8. After importing the data, copy all files from directory (Drive letter):SD-datenE70DATAgdaten to directory (Drive letter):EC-APPSNFSDATAGDATEN, overwriting all existing files.
Note: If you use Progman v.30 for updating WinKFP, it has error in file GDATENSgidc.as2. Simply open this file with Notepad and delete line 165.
WinKFP is ready for programming
Hardware:
A PC (Operating system: Win XP 32 bit /VMware Win 7 32 or 64 bit) An INPA/EDIABAS K+DCAN USB Diagnostic cable (cheap €19 in eobd2.fr)
How to setup BMW Standard Tools 2.12?
Step 1: Download BMW Standard Tools 2.12
Download here and install follow system prompts:
http://www.mediafire.com/download/qldyddn48ffzrwn/BMW+Standard+Tools+2.12.rar
Step 2: Download and install INPA
http://www.maxdown.org/download.php?file=BMW%20Inpa/Ediabas%20v5.06&host=b
Step 3: Download and install NCS Expert ENG
Download NCS-Expert software here and install
http://www.mediafire.com/download/en2xcszq46vaipm/NCSEXPER32_ENG.zip
Step 4: Download and configure INPA K+DCAN cable
Make sure your EDIABAS should already be configured to STD:OBD for use with INPA cable.
Download EDIABAS configurator here:
http://www.mediafire.com/download/x1r66eesv14lx88/ediabas+konfigurator2.0.0.exe
This tool (in C:EDIABASEdiabas-Konfigurator folder) allows you to easily change the ediabas.ini to your desired interface. So if you are switching from INPA to E-Sys you could use this to switch from STD:OBD to ENET. Set COM port for INPA cable Connect the INPA DCAN cable with PC
Install device deriver Come to My Computer>>Device Manager>>Ports (COM&LPT) In this case it's COM5. We need to change this in the obd.ini file located in the c:ediabasbin folder. Right click on your INPA cable driver for example mine is labeled 'USB Serial Port' and click on properties. Now in the property window click on the advanced tab.
Now every driver is different but the important part is the settings such as latency timer and received and transmit bytes. See pic bellow for the ideal settings. You may also change the COM port number here as well for tutorial I left it at 5. Once your changes are done we can proceed by clicking OK to accept the changes. No close all windows to return to the desktop.
Step 5: Change the OBD Browse to C:EDIABASBIN and find file obd.ini and open it with an editor (e.g Notepad) First 3 lines will look like this.. [OBD] Port=Com1 Hardware=USB Need to change the Port to reflect our INPA cable which in our case is COM port 5. So change it to look like this.. [OBD] Port=Com5 Hardware=USB When done click File -> Save and exit
NOTE: Remember which USB port you connected your cable to as plugging it into a different USB port will allocate the INPA cable to a different COM port and neither tool will see the cable until the original USB port is used again or changed in device manager and obd.ini as mentioned above.Now to test if your cable installed correctly. Plug it into the vehicle's OBD port and open INPA.
Step 6: SPDATEN Files Download and install SPDaten files (always recommend the latest)
in this case it is 50.2 until I finish zipping and upload SPDatens 51.0 and upload it to share. (Follow the instructions provided at the end of the blog labeled 'How to start WinKFP' which will explain how to import the SPDaten files to WinKFP)
Once downloaded you can now
**EDITED 10-12-2013**
For NCSExpert to install or update the daten files, copy the files from SP-daten-E##daten to the C:NCSEXPERDATENE## (where E## is whatever chassis you're updating). You will also want to copy the files from SP-daten-E##SGDAT to C:NCSEXPERSGDAT (they're not separated into different chassis in NCS Expert, so you just want to copy and paste everything to that directory. Overwrite everything it asks about). Then copy the files from SP-daten-E##ECU to C:EDIABASECU
After copying the daten files to c:NCSEXPERDATENE## copy the following files to the following locations:
copy C:NCSEXPERDATENE##*.000 C:NCSEXPERDATEN copy C:NCSEXPERDATENE##*.DAT C:NCSEXPERDATEN copy C:NCSEXPERDATENE##*.ASC C:NCSEXPERDATEN
PS: How to start WinKFP?
1. Install WinKFP and come to direction
2. After installation the directory (Drive letter):EC-APPSNFSSGDAT contains file CABI.h only, and doesn’t contains files, required for working.
3. Mount the Progman disk in virtual drive (or insert in usual DVD-drive), extract all files SP-daten-Exx.rar from directory (Drive letter):CIP-Installerbin, each one in its own directory. (You must get directories like SP-daten-Exx)
4. Now copy all *.IPO files from every directory (Drive letter):SP-daten-Exxsgdat to directory (Drive letter):EC-APPSNFSSGDAT. For this purpose better use Total Commander, it allows to overwrite elder files with newest. This directory now looks like this:
5. In the same way refresh directory (Drive letter):EDIABASEcu with files taken from (Drive letter):SP-daten-Exxecu 6. Run WinKFP
6. Run WinKFP software
7. Choose “Import/Export – Import – Assemly line data” and import all data needed from directories (Drive letter):SD-daten-ExxDATA Details how to import assembly line data are given in official manual for WinKFP
8. After importing the data, copy all files from directory (Drive letter):SD-datenE70DATAgdaten to directory (Drive letter):EC-APPSNFSDATAGDATEN, overwriting all existing files.
Note: If you use Progman v.30 for updating WinKFP, it has error in file GDATENSgidc.as2. Simply open this file with Notepad and delete line 165.
WinKFP is ready for programming